Advancing little by little with current projects

Hello all,

This weekend I did a very tiny step on the current projects but it was a very good step for me to know where I am with these and what is coming next, alternatively I also have two good news.

On regards the B737NG cockpit:

I’ve finally got a piece of a composite fiber panel which is 10mm thick and that I cut down to 30x30cm, later I draw a grid of 5x5mm so that I could place all the elements of the 1/12 B737NG cockpit and start to see where everything has to go.
I am going to be using this grid for reference and symmetry since one of the steps I want to do later is to start with the glareshield and that will lead me to complete the front section structure.

Now, to hide all the rear side of the panels, I’ve considered two options; make just a flat wall or make the actual B737NG shell, so a portion of the cockpit would actually be a portion of the fuselage.
One of the things that I must keep in mind is to prevent the cockpit to have lots of shadows and therefore become dark, so I am studying every possibility and the same applies with the overhead panel. Perhaps the best choice would be to do half the shell such as a “cutaway” model and thus allowing the cockpit to have plenty of natural light.

While positioning the different elements, I realized that some work has to be done on the FMC pedestal panel and the throttle quadrant structure for them to fit better. I will actually set the center of the elements on the FMC pedestal since from it, every other panel follows.

Before I move onto the glareshield, I will finetune these unions as well as those for the MIP/sidewalls.

 

As for the B747-8F/-400F deck set:

I have been able to add  two new ribs which are fundamental to hold the deck as well as be a part of the AFT cargo holds. Now that the two rear ribs are made, I will proceed to make the last section of the deck.

I am also starting to study how the rear end wall will fit in the tail section. I am trying to avoid to end the deck with just a circular part with the shape of the fuselage, what I intend to do is create a conic effect as the wall gets smaller inside the tail cone.
This rear wall will be fitted in the fuselage section and will then fit inside of the tail cone once this is attached to the fuselage. The deck set won’t include the tail cone, so that will be cut off from the fuselage kit and placed onto the casted fuselage.

One of the things I am concerned about is that if I add a “false” cone to create that effect, the model may go “nose up”, so I am also considering using ballast towards the front section of the fuselage.

 

I am advancing very slowly with everything, perhaps I should restructure my schedule but I don’t want to leave a project for too long time or else I will forget where I left it. This coming weekend I would like to at least have the LEAP-1A engine with the panel lines engraved and complete the rear section of the cargo deck. As for the B737NG cockpit, I will require a longer “session” to do the steps mentioned at the beginning, but now that I know what do I have to do next, I feel more confident and wishing to start adjusting those panels very soon.

On regards the two good news; one is that this past weekend I have been experimenting with a filler for the polyurethane resin and I am very happy about how it performed, this will therefore save a lot of costs to produce the B737NG cockpit since I want to make the different panels and pedestals solid, saving costs with this material will also represent in a cheaper price for the product. I liked the initial test very much, so I am really looking forward to make use of this on the cockpit.

I am also considering using the filler for the 747-8F/-400F cargo fuselage, but for that I still need to do another test.

The second good news is that I am doing some tests in order to achieve the white of the decals to be more opaque on bigger dark areas. It does not mean that the whites aren’t opaque now, but that I may be able to add the white with less decal elements. This will only work on bigger decals such as tail logos or the overwing emergency exit marks.
It is something that I am still experimenting with but that the upcoming liveries will be designed having this in mind.

Wish you all have a very nice week!

Best wishes,
Guillem

LEAP-1A Getting the main shape done

Good weekend everyone,

Today I want to give a very little update on the LEAP-1A status since I was able to continue working with the shape and add that sort of bulge characteristic of this engine.

There is still a little bit to modify on the bulge, have to move the mass a little bit forward and double check again with the blueprints. Once this is done, I will do a casting of this part in order to start adding the panel lines, following this step, I will then begin working with the pylons.

I also want to say that I am currently studying the next steps that have to be done with the B737NG cockpit project. This is what happens when you leave something for a while, you need to get back in time and check what was the last thing done in order to keep advancing from that point.

The B747-8F/-400F project is momentaneously on pause as I am gathering a little bit more material and once the LEAP-1A is finished, I plan to work alongside with the deck set and with the new FMC15i cargo loader, that will be the first GSE of this year that I will make, so I am hoping to make it as detailed and realistic as possible, I must give a huge thank you to my friend Michael who has given me plenty of reference photos to make this model as best as possible.

Now that the decal liveries are uploaded, I will try to keep them in stock as regularly as possible and will also focus on creating new ones. There are some colorful ones that catch my attention that I would really like to make, but there are also other older liveries non existant nowadays that are also my wish to make. I look forward to move onto a different model other than the A320/A320Neo/A350, so I plan to continue with a Boeing bird next.
I will also put special attention to liveries of aircrafts carrying the LEAP-1A engines since I have been a little bit more limited with the PW engines so far, most Neos are wearing the LEAP engines. A321Neo liveries are also on my plans.

 

Wish you all a very nice Sunday and hope to give another update on the next weekend, hopefully with more info on the current project’s progress.

Best wishes,
Guillem

Livery decals available

Hello everybody,

Finally after several days of practically non stop, the livery decals are available. I must admit that there aren’t as many quantities as I wanted just yet, one of each isn’t much, but because it is the start, quantities are a little bit limited.
As I still don’t know very well which livery will be requested most, more stock will eventually be produced. There is more material on the way, it is a start, so it is my goal to keep these available, so part of this update is to say that from now on, availability of these will be more frequent.

I wanted to share a few photos that I took of the first prints, I really hope that these will be of your liking. You will find more at the store for every specific livery.

 

Work will continue this weekend with the LEAP-1A engine and I am also going to do a review and a list on steps that have to be done next with the B737 cockpit project.

Best wishes,

Guillem

Upcoming livery decals

Hello all,

Last weekend I wasn’t able to work and give an update on the 747 cargo and Leap-1A projects since I am very busy working with the decals. Everything is being finished and printing will start very soon as decals will be available on Friday.

I have been writing down some extra information for certain decal sets in which I give a tip for that specific livery on how to place a particular decal, specially cheatlines. I wanted to give as much information as possible.

Three new liveries will be available; the A350 Air China “Horticultural Expo ’19” colors, the Hong Kong Express A320Neo and the Brussels Airlines A320.

All other liveries will also be available with the exception of  the A320 Lufthansa “Starhansa”.

 

I will be updating the product images during the week.
I have been doing lots of testing during the last months and set up the decals to be printed as best as possible, I really hope you will like these decals!

Best wishes,
Guillem

LEAP-1A First work in progress

Hello everyone,

This weekend I have been working on the LEAP-1A engines after having made the P&W set for the A320 family, and I thought to share how is the progress so far.

Before I show the pictures of the work done, I want to show one that ilustrates the basic physical differences between both engine models:

As you can see, both engines are quite different when examined carefully, it may be easy to not to know which engine is which on a real aircraft at first glance, so one of the things I do to differentiate both engines is to look at the nozzle tip. The LEAP-1A has a little protuberant tube whereas the P&W don’t.

The LEAP-1A also features a very different shape on one of the sides of the cowl creating a kind of a lump. There are many other differences on the pylons as well, being the one for the LEAP-1A  a little bit longer. I am working on the shape with the real dimensions of the engines.

Here is one of the first steps that I’ve done:

I started by using one of the basic shapes of the P&W and modified accordingly, the outer ring is also wider on the LEAP-1A so I was trying to make that area while afterwards I realized that there wasn’t enough material on the inside to give it the proper thickness.

So I decided to sand down kowing that I was also making the engine shorter, what I did later was to add an extension in the middle to get back the distance I “ate” sanding that down.

At the moment the engine does not have that lump as it had in the second picture, but there is the main shape done, however yet to be polished and to have added the lump as well as other details.

I casted the engine as it is because that is the master part, if anything wrong happens to it, there is a chance of having to start all over again. This is a process that I do in certain circumstances pretty much like a “backup copy” so that in case anything wrong happens, you can go back to a certain point of the process.

There is still a lot of work to do, although I have used the basics of the P&W engine, after the cut I had to do, only a 20% remains from that engine and this will also be modified somehow, what I wanted is to make use of the P&W in order to have a “skeleton”, a basic shape to start working with.

You can also notice that the LEAP-1A is a bit flatter than the P&W whereas the P&W seems to be more rounded towards the end of the cowl, it has a more remarked slope.

Still a lot to do, but I hope this one won’t take me as much time as the previous engines did!

Best wishes,
Guillem

Scroll to top