Boeing 747-8F – Cargo deck interior

Hello all,

These last few days I have been thinking about the next GSE and airliner models that I would like to do, and so I thought to start the list with a project that I have been wanting to do for a while.

This project may be a little long but I am sure it will be challenging and enjoyful. The lenght of this project will be determined from the process of secondary items that will be linked very closely to this project.

One of the parts that I like most of  making these models is to gather as much information as possible; numbers, sizes, and lots of photographs. That is the only way to do things properly in scale and I think it is a very important factor, because it is easy to do something a couple milimeters longer which would be about 30cm longer in the real element.

So from here, if anybody by any chance has access to one of these -8F or -400F freighters, I would be enormously grateful to receive reference photos that will surely help me a lot with this build and make it as accurate and detailed as possible.

This B747-8F project will consist of the representation of the fully raised nose cargo door and fully opened side cargo door, with a cargo bay which will include the interior panels that will cover the whole inside of the model. This project will also include decals, these will be used for several things such as panel illustrations, and other signs.


Two of secondary items that I mentioned before that may be build alongside this projects are; cargo pallets and a new cargo loader. The Commander FMC15i bridge can reach 3,55 meters, while the distance of the floor to the rollers of the B747-8F is of 5,05 m (lightweight aft) and 4,72m (heavyweight fwd). Thus the standard Commander FMC15i would not be able to reach the nose height.

That is one of the reasons why these loaders can also be supplied with a double sill, which would increase the elevation. However in this case I am still unsure about if I would like to make a new and bigger loader or create a variation with the double sill from the current model.


Things that concern me are how to build-add the whole cargo compartment inside the kit’s fuselage, which for this build, I am going to be using Revell’s Boeing 747-8F kit. But that is something I will be thinking about prior doing any cuttings.

This leads me to show a first photo where I intend to do a cut:

Naturally, the nose door will be cut out from the fuselage, but so will be the front section. The reason to cut from the mark I made is for some reasons:

1- Once the nose is separated, there is a lot of things going on in that front section, such as the different elements like the hinges which will be placed on the plastic profile, the structure right under the cockpit windows etc.

2- To ease on the building/adding the whole set. Although the nose can be considered a separate part, there is also going to be detail on the forward section, so I think that having that whole section will be later easier for everybody to just make a cut on the kit’s fuselage and incorporate the front detailed section.

The place where I situated the cutting line was decided based on the panel lines. I would not like to cut on top of a fuselage line, because when joining the front section, the addition of putty or the work with the sanding paper would erase that line. So in this way is very easy to glue the front section in a smooth area, add masking tape at both sides while applying putty or sanding and therefore conservating the vertical panel lines.

Obviously it is impossible to do a cut such as this without having to go through a panel line, but it is easier to do a small cut where the horizontal lines meet rather than a long cut where the vertical panel lines are.

3- It will be easier for me to work with both front section halves glued, since I will be placing the structure under the cockpit windows etc.

4- The connection of the ladder to the cockpit, which may lead me to make a cut past the L1 door so that I can make the door opened and provide the door already open in the fuselage. This makes me think that it is possible that photo etched parts (like the ladder) will also be done.

Cutting past the L1 may be the best solution, after all it is normal the L1 to be open while loading the cargo, so that is something I will probably do.


Another of the things that I will be taking into consideration is the possibility to port this to a -400F type. So I will take a look to see if the floor / rollers layout is different from both the -8F and the -400F.

A bit long project in which I should consider all possibilities before doing a cut, despite some of the new GSE items I like to make, the fuselage of this 8F is already on my desk.


In a few days I would like to comment on which will be the other items I would like to start, but in the meantime, I continue preparing the upcoming stock units of the items I already made.

Best wishes,



B737NG PFD and ND done

Hello everybody,

I have been able to make the PFD and ND for the B737NG cockpit project this last weekend. Note that there is still a lot to do on that main instrument panel, add all the buttons, screws etc.

These screens will have a decal on them, and I would like to supply different type of decals for different flight stages (IRS alligment, before takeoff, cruise etc). I would also like to include a thin acetate sheet with the screen outline drawn to aid on cutting which later will be placed on top of the decal to create the crystal effect.

I think that before advancing into more details, I should start to make the basic shape of the autopilot panel and glareshield so that I can prepare the base of the cockpit where all the panels and structures will go.

Best wishes,


Upcoming livery decals – GSE stock started


I have recently started to make the stock units for the GSE using the new molds. I am happy with the result as from what I saw, I can produce these resin parts just a little bit quicker than before without sacrificing detail and more orderly. It was really pointless to have so many molds per model, so organizing the parts properly made me save some time.

This was done because of what I have learned after casting each new model I made and after many trials and errors on the way, so I applied these techniques for the older models in the process of renewing the molds.

On the other hand, I have been working on a new livery decal set, this time for the Airbus A350. So far I have made a generic base decal and the China Airlines “Pheasant” livery.

I want to try something new for this model, so once I receive the first print, I will mention more about it and actually do a little review of the A350 decals.

I also want to write a post in the next days with a list of upcoming GSE and airliner items that I intend to make, so although I will be busy in the next weeks preparing the stock, I will also keep on thinking on the next projects.

Hopefully this weekend I can have some time to work on the PFD and ND of the B737 cabin project.


Best wishes,


New molds finished and tested

Hello everyone,

I have been working during the last days into the new molds and finally I finished to make them all. As I explained in my previous post, some parts that were more complex to cast than others, were splitted to make an easier cast and therefore having better molds which result in a quicker and easier work.

I have made a test with the FMC15i cargo loader with the new molds, these don’t change the final aspect, but this was needed to check if all the parts from the new molds fitted well as this is one of the most complex GSE models I made so far. While I was building this model I took photos of the entire process which I hope to upload here and hopefully these can assist on your build.

The WiFi (Honeywell’s Jetwave MCS 8200) radome has also been casted and will be available once the online store is open. In the photos below it was tested on an A350.

I wanted to advance with the B737 cabin project during the last holiday, but I had some issues making the PFD and ND displays so I am hoping to fix that during the next weekend. I did not have much free time to advance with the cabin as my main goal was to finish the new molds. Now that they are finished, I am starting to make new units of these GSE items.

I will update the blog in a few days with some info on the livery decals and the upcoming stock.


Best wishes,


WiFi radome


I have been able to complete the new molds of the 1/144 catering truck and the 1/144 pushback truck, there are still the cargo loader molds and GPU molds to be made.

Making the molds may be a little time consuming thus I did not have much time to advance with the B737NG cabin project on the weekend. With less time, I decided to make a new WiFi radome; this WiFi radome is mainly seen on B777, A350, B787, B767 and also on smaller airliners such as the B757, B737 and A319/A320/A321. The one that I tried to represent is the Honeywell’s Jetwave MCS 8200.

Some airliners using that WiFi radome are: A350 aircrafts, United’s B777, Lufthansa’s A320, ANA’s B767, 777 and 737, LOT 787, Air Europa B787 etc.

Following this antenna, I also would like to make the ADF antennas which are often included in both halves of the model’s fuselage and in my opinion, result in a little hasle when applying putty and sanding the fuselage union.

Making new molds

Hi all,

I am writing this entry to comment on the stock of the older GSE models. As you may probably know, sometimes molds can break or deteriorate with time because of several reasons; use, humidity etc. So right now I am in a transition process in which I am making new molds for the following items:

  • 1/144 Towbarless pushback.
  • 1/144 Catering truck.
  • 1/144 Cargo loader FMC15i.
  • 1/144 Ground power unit.
  • 1/144 LD3 containers.

I am obliged to make them new because using old molds means that there is going to be a loss of detail, so it should be important to renew the molds from time to time.

I am also re organizing in which way the parts will be casted so that I can:

a) Make the parts easier to prepare, by requiring less sanding lines.

b) To shorten the making process per unit.

Parts re arrangement for the new molds.

For the catering truck, I currently use 11 molds, but with a re arrangement I can use 7 molds.

Some of these modifications will represent a slight change in complex parts for casting, so these have been disassembled into two, but the final result will be the same. Therefore, a small update on the pushback truck, catering truck, and cargo loader instructons will be required.

The recent items:

  • 1/144 Belt loader.
  • 1/144 Carts (A and B).
  • 1/144 baggage.
  • 1/144 AKH containers.

Will be produced with their original and recent molds.

As for the Neo engines; I am preparing stock units of them so they will be available once the stock for the GSE items is completed so that the new online store can be opened with both these items available.

I would like to write a little bit on regards the airliner livery decals, but I currently can’t give much more info at the moment as tests haven’t been done yet for the A350 decals. I am currently designing the base decal for the Airbus A350 and at the same time designing a new type/style  of decals (I think) which will be tested on the A350 and for which I hope they will come out alright.


Best wishes,


Posts navigation

1 2 3 10 11 12 13 14 15 16 17
Scroll to top